Cloud-electronics DCM1 Instrukcja Użytkownika Strona 65
- Strona / 79
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
DCM1 & DCM1e Installation and User Guide V1.0 65
PCB jumper locations and settings.
The DCM1 has various internal jumpers, the setting of which
may require alteration during installation. The table below
lists each jumper and its purpose, together with the factory
default setting.
The diagram below the table shows the locations of the internal
jumpers (not to scale). In the case of the jumpers having two
possible positions, the black square in the symbol indicates
the default setting. If any jumpers need to be changed, undo
the eight screws securing the top cover of the DCM1, and
remove it. Use a pair of snipe-nosed pliers to gently remove
the jumpers, and to reposition them if necessary. Rex the
top cover using the original screws.
JUMPER NAME PURPOSE DEFAULT
J2 PM/CDPM bus termination
ABSENT = PM/CDPM termination OFF
PRESENT = PM/CDPM termination ON
Present
J6 CDR-1 Port A bus termination
ABSENT = CDR-1 Port A termination OFF
PRESENT = CDR-1 Port A termination ON
Present
J7 CDPM ground link
ABSENT = PM/CDPM signal ground “lifted”
PRESENT = PM/CDPM signal ground connected
Present
J8 Reset Installer PIN
Reinstates original factory key for enabling Installer
Mode. Replace after use.
Off
J9 Force Factory Defaults
Reinstates original factory settings except Input/
Zone/Group names. Replace after use.
Off
J10 Bootloader baud rate: select 1
Changes baud rate for rmware updates. See table
page 70.
Off
J11 Bootloader baud rate: select 2 Off
J13 CDR-1 Port B bus termination
OFF = CDR-1 Port B termination OFF
ON = CDR-1 Port B termination ON
Present
J14 PM/CDPM power link
OFF = PM/CDPM power off
ON = DC power for PM/CDPM is available at
CDPM/PM IN connector.
Present
J24 Paging mic phantom power
OFF: paging mic phantom power OFF
ON: paging mic phantom power ON
Off
J25 EQ Module: Zone 1 R
Must be present if no EQ module is tted Present
J26 EQ Module: Zone 2 R
J27 EQ Module: Zone 3
J28 EQ Module: Zone 5
J29 EQ Module: Zone 6
J30 EQ Module: Zone 7
J31 EQ Module: Zone 4
J32 EQ Module: Zone 8
J33 EQ Module: Zone 1 L
J34 EQ Module: Zone 2 L
NOTE: J15, J16, J17 and J18 are reserved.
J2
J
6
J
13
J
7
J
14
J
8
J
9
J
10
J
11
J
15
J
16
J
17
J
18
J
32
J
27
J
28
J
30
J
31
J
29
J
26
J
34
J
33
J
25
J
24
(UPPERPCB)
(LOWER PCB)
KEY:
Jumper with two possible positions; black
square indicates factory default setting.
Jumper with one position (i.e., present or not)
- DCM1 & DCM1e 1
- Contents 2
- Safety Information 4
- What’s in the box 5
- Section 1: Overview 6
- System Components 7
- Optional components 7
- Cloud DCM1 Utility Tool 8
- System Capabilities 9
- Applications and Examples 11
- System 2 12
- System 3 13
- Section 2: Installation 14
- Description of rear panel 15
- Hardware considerations 17
- System Connections 17
- Standard connection: 18
- CDR-1 Remote Control Plates 19
- Connections 20
- Network Terminations 21
- Mic and Line Input Modules 22
- Connections and wiring 23
- PM Terminations 24
- PM DC power 24
- Adjusting paging levels 24
- Zone paging outputs 24
- Paging microphone input 25
- Paging Access Connector 26
- Section 3: Conguration 27
- (DCM1e only) 28
- Groups menu 29
- Installer Mode 30
- SELECT INPUT 31
- Routing Menu 32
- Output or GPIO mode 33
- Rotary Control sets offset 34
- System Menu 35
- Rotary Control selects Zone 36
- Press to change mode 36
- Press moves to next character 36
- Numeric buttons select Input 36
- Numeric buttons enter key 38
- Rotary Control sets Baud Rate 38
- Priorities Menu 40
- Rotary Control sets value 41
- Numeric buttons select Zone 43
- Rotary Control sets level 45
- Other DCM1 adjustments 46
- Current Zone 47
- Reception 47
- Normal Mode Installer Mode 48
- Display adjustments 50
- Inactivity Time 50
- Assign Zone 50
- Security 51
- Browser compatibility 52
- Quick Troubleshoot 52
- Grouping 53
- Security Page: 54
- Input Status: 56
- Network: 56
- Device Info: 56
- Change PIN: 57
- Conguring the DCM1 with the 58
- DCM1 Utility Tool 58
- Inputs Tab 59
- Outputs Tab 59
- Installer Key Tab 60
- System Tab 60
- System Interconnections 62
- Music Mute Input 64
- RS-232 Control 64
- Ethernet interface 64
- Port parameters 66
- 1. Input Selection: 67
- 2. Zone Levels: 67
- 3 . Enable/Disable Groups 67
- 4 . Enable/Release Paging 67
- PSU capability 69
- RJ45 pinout 69
- DCM1 only: 70
- DCM1e only: 70
- Record value (if used) 74
- SYSTEM MENU 74
- EMC considerations 75
- Specications 75
Powiązane produkty i podręczniki dla Audio Cloud-electronics DCM1
(38 strony)
(5 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.080 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji